Led_module_init okTC3162 LED Manager 0.1 init
#Huawei hg532e specs driver
Usbcore: registered new interface driver usbtestĪTP_FLASHCBB_Init: flash_erase_buffer ptr 81110000 size 65536 Usbcore: registered new interface driver optionĭrivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
#Huawei hg532e specs serial
Usbcore: registered new interface driver usbserial_genericĭrivers/usb/serial/usb-serial.c: USB Serial Driver coreĭrivers/usb/serial/usb-serial.c: USB Serial support registered for option1 Usbcore: registered new interface driver usbserialĭrivers/usb/serial/usb-serial.c: USB Serial support registered for generic Usbcore: registered new interface driver usb-storage Usbcore: registered new interface driver usblpĭrivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Usb usb2: configuration #1 chosen from 1 choice Rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x1fba0000 Rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 Rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller Usb usb1: configuration #1 chosen from 1 choice Rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver Rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x1fbb0000 Rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 Rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller Mtd: partition "mainfs" doesn't start on an erase block boundary - force read-only Mtd: partition "main" doesn't end on an erase block - force read-only Mtd: partition "flag" doesn't end on an erase block - force read-only RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Squashfs: version 3.2-r2 (5) Phillip Lougher TCP: Hash tables configured (established 1024 bind 1024) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) IP route cache hash table entries: 128 (order: -3, 512 bytes) Time: MIPS clocksource has been installed. Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc. Usbcore: registered new device driver usb Usbcore: registered new interface driver hub Usbcore: registered new interface driver usbfs Registering PCI controller with io_map_base unset (2388k kernel code, 3660k reserved, 683k data, 140k init, 0k highmem) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) PID hash table entries: 128 (order: 7, 512 bytes)ĭentry cache hash table entries: 4096 (order: 2, 16384 bytes) Synthesized TLB modify handler fastpath (31 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB refill handler (20 instructions). Primary data cache 32kB, 4-way, linesize 32 bytes. Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes. Kernel command line: console=ttyS0 rootfstype=squashfs panic=1 es=1
#Huawei hg532e specs full
Using this phython script we can make a full backup without desoldering the flash chip: Then send via XMODEM your recovery bootloader: recovery.img Now you cand send via XMODEM a full backup, and flash it. Press the reset button while powering up the device: RT63365 at Tue May 8 19:47: version 0.8 The SoC has an embedded bootloader that can be used when there is no bootloaderĪt the flash chip. Press any key in 3 secs to enter boot command mode.Įrase_write Write to flash from src to dst.Ĭpufreq / Set CPU Freq (freq has to be multiple of 6) There are some commands available for unbricking the deviceįound SPI Flash 8MiB S25FL064A at 0xb0000000 We can break into the Bootloader command line by pressing